Skip to Content

Diamond Locks logoRapid Product Development - Pioneering new solutions. Read About Us.

Programming Guide

 

 

Codes

  • The Cabinet Lock has three code levels available
    • Master-Code
    • Sub-Master Code
    • User Code
  • The Cabinet Lock is supplied with two factory set codes
    Master Code: 11 33 55 77
    User Code: 22 44
  • When fitted immediately change the Master Code and User Code
  • All Master Codes and Sub-Master Codes are 8 digits long
  • All User Codes are 4 digits long
  • The lock 'open' time is set at 4 seconds

 

 

Functions

Before programming select the most appropriate option. The lock can be set in either of two options dependant on the application.

A) Repeated Use

Important Note: This is the default function and is already pre-programmed in new locks.

This is the most common function and is used where the same code will be repeatedly used.

B) Single Use

The User enters a single use code which will lock and then open the lock once only and then be erased.

This function is used for short term, multi occupancy applications e.g. a locker in a leisure centre.

To select B) single use:
#Master Code Accepted 24 AcceptedAccepted

The lock will now remain open until the next single use code is entered into the lock as follows:
Step 1: # enter 4 digit code Accepted close the locker which will now be locked.
Step 2: Enter same 4 digit code AcceptedAccepted lock will open and remain open until next 4 digit code is entered.

Example:
Step 1: #1234 Accepted close the locker which will now be locked.

Note: When locked in this mode the red Red LED will flash every 5 seconds to indicate locker is locked.

Step 2: 1234 AcceptedAccepted locker now open – remains open until next single use code is entered.

Note: To reset to default function
A) use the following key sequence:
#Master Code Accepted 26 AcceptedAccepted
Example: #11 33 55 77 Accepted 26 AcceptedAccepted

 

 

Operating Instructions

Note: The Cabinet Lock has a 5 button keypad and a # button. The # button is hidden beneath the handle when in the locked position.

The lock has the following code levels:

  • Master Code can:
    Open the lock
    Change the Master Code
    Set / Change / Delete the Sub-Master and User Code
    Select between repeated use and single use codes
     
  • Sub-Master Code can:
    Open the Lock
    Change the Sub-Master
    Set / Change / Delete the User Code
     
  • User Code can:
    Open the lock
    Change the User Code

A code cannot be programmed into more than one level.

 

Lost Code Procedure
Note: The procedure requires the door to be open

  • Remove the rear-fixing bolt and swing the lock over the edge of the door to reveal the battery compartment
  • Remove one battery
  • Press and hold the 1 button, replace the battery, the blue LED will flash twice, release the 1 button. Within three seconds press the 1 button three times. The blue LED will flash twice and the lock will have reverted to the factory master code 11 33 55 77 and all other stored settings will be erased.

Penalty time

  • Entering three incorrect codes will cause the lock into shutdown for 10 seconds.

Battery Power

  • The Cabinet Lock should provide well in excess of 15,000 openings, of 4 seconds each, from 2 x AAA 1.5v cells.

Low Battery

When the battery power is low the Red LED will flash 3 times before the Blue LED flashes to signal acceptance of the code. Batteries should be changed as soon as this happens. The lock will operate for 100 times with low battery.

Battery Failure Override

The Cabinet Lock has been designed so an external PP9 battery can be placed against the contact points surrounding the Blue and Red LED's so the lock can be opened to replace the batteries should they fail.

The procedure is as follows:

  • Place the contact points of the PP9 battery against the contact points surrounding the Blue and Red LED's
  • The positive + PP9 terminal against the Red LED contact point and the negative – PP9 terminal against the Blue LED
  • Enter the Master Code
  • The motor will withdraw the locking pin allowing the lock to be opened
  • Fit new batteries by removing the upper fixing bolt and swinging the lock down over the edge of the door. Refit the lock.

 

 

Programming

To program – the lock must be in the open position with the # button visible. Every program command must commence by pressing the # button, followed by either the Master Code, Sub-Master Code or User Code.

Master Code Commands

CHANGE THE MASTER CODE
Key Sequence
#Master Code Accepted 01 Accepted New Master Code Accepted New Master Code Accepted Accepted
Example: #11335577 Accepted 01 Accepted 12345678 Accepted 12345678 Accepted Accepted
Result
Master Code has been changed to 12345678
 
SET OR CHANGE THE USER CODE
Key Sequence
#Master Code Accepted 02 Accepted User Code Accepted Accepted
Example: #11335577 Accepted 02 Accepted 6666 Accepted Accepted
Result
New User Code 6666 now operative
 
DELETE THE USER CODE
Key Sequence
#Master Code Accepted 03 Accepted Accepted
Example: #11335577 Accepted 03 Accepted Accepted
Result
User Code deleted
   
SET OR CHANGE THE SUB-MASTER CODE
Key Sequence
#Master Code Accepted 04 Accepted Sub-Master Code Accepted Sub-Master Code Accepted Accepted
Example: #11335577 Accepted 04 Accepted 87654321 Accepted 87654321 Accepted Accepted
Result
Sub-Master Code 87654321 now operative
 
DELETE THE SUB-MASTER CODE
Key Sequence
#Master Code Accepted 05 Accepted 05 Accepted Accepted
Example: #11335577 Accepted 05 Accepted 05 Accepted Accepted
Result
Sub-Master Code deleted

Sub-Master Code Commands
CHANGE THE SUB-MASTER CODE
Key Sequence
#Sub-Master Code Accepted 06 Accepted New Sub-Master Code Accepted New Sub-Master Code Accepted Accepted
Example: #87654321 Accepted 06 Accepted 101010 Accepted 101010 Accepted Accepted
Result
Sub-Master Code has been changed to 101010
 
SET OR CHANGE THE USER CODE
Key Sequence
#Sub-Master Code Accepted 07 Accepted New User Code Accepted Accepted
Example: #87654321 Accepted 07 Accepted 9999 Accepted Accepted
Result
User Code 9999 now operative
 
DELETE THE USER CODE
Key Sequence
#Sub-Master Code Accepted 08 Accepted Accepted
Example: #87654321 Accepted 08 Accepted Accepted
Result
User Code Deleted

User Code Commands
CHANGING THE USER CODE
Key Sequence
#User Code Accepted New User Code Accepted New User Code Accepted Accepted
#2244 Accepted 6688 Accepted 6688 Accepted Accepted
Result
User Code now 6688

 

Download the printable version of this page Download the printable version of this page (pdf)

 
  • If help is needed before, during or after installation of your digital keyless door lock, call our freephone helpline 0800 393 405.
© Copyright 2007 Diamond Locks and its licensors - All Rights Reserved                           Site Map | Privacy Policy | Back to Top